Sign in
Tell us where you need an hvac pro. We'll do the rest.
Rogue GRFX
About us
Don't waste time and money on buying and painting a new set of body panels. Rogue Grfx kits are easy to install, just clean surface, peel and stick only takes 15-20 minutes to install!
Although Rogue Grfx kits are pre-cut to match the contours of the body panels some trimming is needed.
Also on complex surfaces such as the Hood use a blow dryer to heat decal. Heat while applying helps the sticker material mold to the contour of the hood lines.
Decal Set go on the outside of the body
Body does not have to be new, only Clean of Dirt, Wax or Oils
Our 3m Vinyl uses "Pressure Sensitive Adhesive". While placing the graphic use a light pressure incase you need to re-position the decal. Once Decal is placed in the Perfect spot, apply a firm pressure to "Set" the adhesive.
We use 3M material with Air Release, for a Bubble free install.
Recommended items hobby Knife/Exacto Blade or Similar and Isopropyl Alcohol.
Installation of your Rogue GRFX Decal Wrap onto your body panels is a fairly simple process, however, here are few tips to make the install go even better.
Items Needed
1. X-Acto knife with new blade.
2. Hair dryers or heat gun.
3. Isopropyl Alcohol - For cleaning.
4. Soft lint-free Cloth or Blue Scotts Shop Towel
5. Patience, if you take your time the wrap will come out sick!
If you have a New Clear Body, it is not necessary to paint your body on the inside with lexan body paint we do however recommend it incase you have some decal panels mis-alighned on your install. We recommend either Black and White for a clean look.
Step 1 - Lay out all the body panels so you know which is which.
Step 2 - Remove any stock decals.
Step 3 - Clean all the body panels with Isopropyl Alcohol & Dry with a lint free cloth or Blue Scotts Shop Towel.
Step 4 - From your Rogue GRFX Decal sheet take note, on which panel is labeled to go on First. If not noted then choose any panel you like and go for it.
Step 5 - Begin to install your decal. Peel each piece off the decal sheet and apply to the correct... show more body panel. Slowly apply pressure S from the middle and work your way out to the edges. If you get any wrinkles, carefully peel them back slightly and re-apply.
Note: That there is "Extra" decal on some panels, some pieces are cut with 1/16” extra around the edge to make it easier to apply.
Step 6 - Once all decals are placed apply firm pressure all over the decals to "Set" the adhesive, this is important to make sure the decal holds strong to the body.
Step 7 - Heat up the decal! - Heating the decal does 2 things it "Sets" the adhesive but it also removes wrinkles! If by chance you and some wrinkles the heat will soften the decal and will let you smooth them out. Locate a wrinkle and apply the heat from the gun for 1-3 seconds. You’ll notice the decal is now soft and wants to lay flat. Now is the time to smooth it out (Note: It may be HOT!). Just rub down in those areas and most wrinkles will dissapear. Heat also works great on curved ares. TIP: Start in the middle and work you way to the edges. Note: If using a heat gun be car full to not get too close to the decal you may burn or melt it!
Step 8 - Trimming! Use your Exacto knife to trim the excess decal away from the edges. Do this by slowly pulling the knife (laid almost 90 degrees with the panel) slowly towards you. Note: be careful to keep the knife angle perfect enough to cut the decal but not dig into the panel.
Step 9 - If your body uses screws to mount or body mounts make sure to trim those areas. Just insert the knife through the hole and give it a quick spin around.
Step 10 - Go show off your rig it's looking good! show more
Although Rogue Grfx kits are pre-cut to match the contours of the body panels some trimming is needed.
Also on complex surfaces such as the Hood use a blow dryer to heat decal. Heat while applying helps the sticker material mold to the contour of the hood lines.
Decal Set go on the outside of the body
Body does not have to be new, only Clean of Dirt, Wax or Oils
Our 3m Vinyl uses "Pressure Sensitive Adhesive". While placing the graphic use a light pressure incase you need to re-position the decal. Once Decal is placed in the Perfect spot, apply a firm pressure to "Set" the adhesive.
We use 3M material with Air Release, for a Bubble free install.
Recommended items hobby Knife/Exacto Blade or Similar and Isopropyl Alcohol.
Installation of your Rogue GRFX Decal Wrap onto your body panels is a fairly simple process, however, here are few tips to make the install go even better.
Items Needed
1. X-Acto knife with new blade.
2. Hair dryers or heat gun.
3. Isopropyl Alcohol - For cleaning.
4. Soft lint-free Cloth or Blue Scotts Shop Towel
5. Patience, if you take your time the wrap will come out sick!
If you have a New Clear Body, it is not necessary to paint your body on the inside with lexan body paint we do however recommend it incase you have some decal panels mis-alighned on your install. We recommend either Black and White for a clean look.
Step 1 - Lay out all the body panels so you know which is which.
Step 2 - Remove any stock decals.
Step 3 - Clean all the body panels with Isopropyl Alcohol & Dry with a lint free cloth or Blue Scotts Shop Towel.
Step 4 - From your Rogue GRFX Decal sheet take note, on which panel is labeled to go on First. If not noted then choose any panel you like and go for it.
Step 5 - Begin to install your decal. Peel each piece off the decal sheet and apply to the correct... show more body panel. Slowly apply pressure S from the middle and work your way out to the edges. If you get any wrinkles, carefully peel them back slightly and re-apply.
Note: That there is "Extra" decal on some panels, some pieces are cut with 1/16” extra around the edge to make it easier to apply.
Step 6 - Once all decals are placed apply firm pressure all over the decals to "Set" the adhesive, this is important to make sure the decal holds strong to the body.
Step 7 - Heat up the decal! - Heating the decal does 2 things it "Sets" the adhesive but it also removes wrinkles! If by chance you and some wrinkles the heat will soften the decal and will let you smooth them out. Locate a wrinkle and apply the heat from the gun for 1-3 seconds. You’ll notice the decal is now soft and wants to lay flat. Now is the time to smooth it out (Note: It may be HOT!). Just rub down in those areas and most wrinkles will dissapear. Heat also works great on curved ares. TIP: Start in the middle and work you way to the edges. Note: If using a heat gun be car full to not get too close to the decal you may burn or melt it!
Step 8 - Trimming! Use your Exacto knife to trim the excess decal away from the edges. Do this by slowly pulling the knife (laid almost 90 degrees with the panel) slowly towards you. Note: be careful to keep the knife angle perfect enough to cut the decal but not dig into the panel.
Step 9 - If your body uses screws to mount or body mounts make sure to trim those areas. Just insert the knife through the hole and give it a quick spin around.
Step 10 - Go show off your rig it's looking good! show more
Recommendations and reviews from 1 person
-
Referral from
August 23, 2013
Rich P. asked:Can anyone recommend a good place to get some custom shirts and harts made I'm in the Market to get some.
John U. replied:https://www.facebook.com/RogueGrfx
New Review
Please wait....
Please wait...
